Most drivers set their side mirrors once, usually so they can see the side of their own car, and never think about them again. Then a car seems to appear out of nowhere during a lane change on the Mass Pike, and they wonder where it came from. It came from a blind spot that better mirror settings could have shrunk.
This guide shows you how to adjust side mirrors and your rearview mirror step by step, explains the wider BGE setting, gives you a quick way to test your setup, and covers the head-check habits every Massachusetts driver needs, mirrors or not.
Quick Summary
To adjust side mirrors, first set your seat, then set the rearview mirror to frame the whole rear window. For the driver’s mirror, lean your head toward the driver’s window and adjust until you just see the side of the car. For the passenger mirror, lean toward the center of the car and do the same. Sitting normally, you should no longer see your own car.
- Seat first, mirrors second: any change to your seat changes what each mirror shows.
- Angle the side mirrors outward: safety guidance describes turning each outside mirror outward by about 15 degrees from the traditional setting.
- Test with a passing car: a car should appear in the side mirror before it leaves the rearview mirror.
- Mirrors do not remove every blind spot: a quick look over your shoulder is still needed before you change lanes or merge.
- The passenger mirror is convex: it shows a wider view, so cars in it are closer than they look.
- Blind-spot warnings are a backup: they help, but you are still responsible for checking.
| Mirror | How to set it | What you should see |
|---|---|---|
| Rearview mirror | Sit normally and frame the whole rear window | The full back window, moving only your eyes |
| Driver’s side mirror | Lean toward the driver’s window, adjust until you just see the side of the car | The lane beside you, with little or none of your car |
| Passenger side mirror | Lean toward the center of the car, adjust until you just see the side of the car | The lane to your right, with little or none of your car |
Want an instructor to check your mirror and blind-spot habits before your road test? Contact CMSC Driving School to book a lesson.
What is in this guide
- In what order should you adjust your seat and mirrors?
- How do you set your rearview mirror?
- How do you adjust side mirrors correctly?
- What is the BGE mirror setting, and is it better than the traditional setting?
- Should you see the side of your car in your side mirrors?
- How do you test whether your mirrors are set right?
- What is a blind spot in driving, and how do you check it safely?
- Why is the passenger side mirror convex?
- Does blind-spot monitoring replace mirrors and head checks?
- Do mirror settings change for parking, reversing, SUVs or towing?
- What should Massachusetts road test candidates know about mirrors?
In what order should you adjust your seat and mirrors?
Adjust your seat first, then the steering wheel, then the rearview mirror, then the driver’s side mirror, then the passenger side mirror. Mirrors are set from your eye position, so if you move the seat after setting them, every mirror is off. This quick routine takes about a minute and is worth doing every time you drive a car someone else has used.
- Set your seat so you reach the pedals comfortably with a slight bend in your knees.
- Adjust the steering wheel so your hands rest naturally at 9 and 3.
- Set the rearview mirror to frame the whole rear window.
- Set the driver’s side mirror by leaning toward your window.
- Set the passenger side mirror by leaning toward the center of the car.
- Test with a passing car the first chance you get, in a parking lot or on a quiet road.
The Massachusetts RMV driver education curriculum includes adjusting seats and mirrors, so new drivers practice this routine early in teen drivers ed in Massachusetts.
How do you set your rearview mirror?
Set your rearview mirror by sitting in your normal driving position and adjusting it until the entire rear window fills the mirror. You should be able to check it by moving only your eyes, not your head. If you need to turn your head to see the back window, the mirror is not set correctly.
- Frame the whole window, not just the lane behind you.
- Center the view so the rear window sits in the middle of the mirror.
- Reset it whenever you change seat position, or after a passenger bumps it.
What is the tab on the rearview mirror for?
The small tab at the bottom of many rearview mirrors switches between day and night settings. Flipping it to night angles the mirror so bright headlights behind you reflect away from your eyes, which cuts glare but makes the image dimmer. Many newer cars use an auto-dimming mirror instead, which darkens on its own when bright lights hit it. Flip the tab back for daytime driving.
How do you adjust side mirrors correctly?
To adjust side mirrors correctly, set each one from a leaning position so that, when you sit normally, the mirrors show the lanes beside you instead of the side of your own car. This method angles each mirror further outward than most drivers are used to, which shrinks the blind spot next to the car.
How do you set the driver’s side mirror?
- Lean your head toward the driver’s window, until it is close to the glass.
- Adjust the mirror until you can just see the rear side of your car at the inner edge of the mirror.
- Sit back normally. You should now see little or none of your car, and more of the lane beside you.
- Set the vertical angle so the horizon sits near the middle of the mirror.
How do you set the passenger side mirror?
- Lean toward the center of the car, above the center console, keeping the seat belt in mind.
- Adjust the passenger mirror until you can just see the rear side of your car at its inner edge.
- Sit back normally and check that the mirror now shows the lane to your right.
Only lean while the car is parked. Never move out of your normal driving position to adjust mirrors while the car is moving.
What is the BGE mirror setting, and is it better than the traditional setting?
The BGE setting, short for Blindzone Glare Elimination, is the wider side mirror setting described above. It traces back to a 1995 Society of Automotive Engineers paper by engineer George Platzer, and federal safety guidance describes it as turning each outside mirror outward by about 15 degrees from the traditional position. It reduces the blind spot and also cuts glare from headlights behind you at night.
| Feature | Traditional setting | BGE (wide) setting |
|---|---|---|
| How to set it | Sitting normally, show a strip of your own car | Lean toward the window or center, then show just the car’s edge |
| What you see | Part of your car and the lane behind you | The lanes beside you, little or none of your car |
| Blind spot | Larger area beside the car is hidden | Smaller hidden area beside the car |
| Night glare | Headlights behind can glare in side mirrors | Much less glare from side mirrors |
| Learning curve | Familiar to most drivers | Feels strange for the first few drives |
| Still need a head check? | Yes | Yes |
The wider setting is not perfect. Some drivers find it confusing at first, because cars move from mirror to mirror instead of overlapping. Give it a week of daily driving before you decide. Whichever setting you choose, the shoulder check stays.
Should you see the side of your car in your side mirrors?
With the wider setting, you should see little or none of your own car when sitting normally. Seeing a large strip of your car means that part of the mirror is showing an area you already know about, rather than the lane where another car could be hiding. Some drivers like to keep a thin sliver of the car in view as a reference point, which is a reasonable middle ground.
If you tip your passenger mirror down to see the curb when parallel parking, remember to set it back before you drive away. Our guide to parallel parking tips for the driver’s test covers using mirrors at the curb.
How do you test whether your mirrors are set right?
Test your mirrors by watching a car pass you on the left and right. With good settings, the passing car should appear in your side mirror before it disappears from your rearview mirror, and it should come into your side vision as it leaves the side mirror. If there is a gap where the car vanishes from every mirror, adjust that side mirror outward a little more.
- Find a safe spot, such as a quiet multi-lane road with a supervising driver, or a parking lot with a helper.
- Watch the car in the rearview mirror as it approaches.
- Note when it appears in the side mirror. It should show up before it leaves the rearview mirror.
- Watch it leave the side mirror and come into your side vision.
- Adjust and repeat until the handoff between mirrors feels smooth.
What is a blind spot in driving, and how do you check it safely?
A blind spot in driving is an area around your car that you cannot see in any mirror while sitting in your normal position. The biggest blind spots sit beside and slightly behind the car on each side. Even properly positioned mirrors cannot remove every blind spot, which is why a quick head check is part of every lane change.
- Check your rearview mirror.
- Check the side mirror on the side you are moving toward.
- Signal to show your intention.
- Turn your head quickly to look over your shoulder through the side window. Keep it brief, because while your head is turned, your eyes are off the road ahead.
- Move over smoothly if the lane is clear, keeping your speed steady.
How often should you check your mirrors when driving?
Check your mirrors regularly as you drive, and always before you slow down, stop, change lanes, turn or merge. Frequent mirror checks keep a picture in your head of what is around you, so you already know where other cars are before you need to move. Our tips for driving in heavy traffic in Massachusetts explain how to keep that picture current in busy lanes.
Why is the passenger side mirror convex?
The passenger side mirror is convex, meaning it curves outward, so it can show a wider area than a flat mirror. Federal vehicle standards require that mirror to carry the warning that objects in it are closer than they appear, because the curve makes cars look smaller and farther away. The driver’s side mirror is usually flat, so distances there look true to size.
- Allow extra space when a car appears in the passenger mirror.
- Confirm with a head check before moving right.
- Do not judge exact distance from the passenger mirror alone.
Does blind-spot monitoring replace mirrors and head checks?
No, blind-spot monitoring does not replace mirrors and head checks. Blind-spot warning systems use sensors to flag a car beside you, and research has linked them to fewer lane-change crashes.
Every system has limits, though, and dirt, snow or ice on the sensors can affect how well it works. Your owner’s manual lists the limits of your car’s system. Treat the warning light as a backup to your own checks.
Driver-assist features can also be switched off or unavailable in some situations, including when you borrow a different car. Building strong mirror and head-check habits means you are ready for any car you drive.
Do mirror settings change for parking, reversing, SUVs or towing?
Your basic mirror settings stay the same in most situations, but you may adjust how you use them. When reversing, turn your body and look back through the rear window, using the mirrors as support. In larger vehicles such as SUVs, vans and pickups, blind spots are bigger, so take extra care with head checks. When towing, you may need towing mirrors that extend past the trailer.
- Reversing: look over your shoulder through the rear window, and check mirrors and any camera as backup. See our guide on how to back into a parking space.
- Shared cars: reset mirrors every time someone else has driven the car.
- Night driving: use the rearview night setting to cut glare. Our night driving tips for new drivers cover glare and headlight use.
- Drivers with limited head movement: supplemental mirrors may help, and CMSC’s adaptive driving program includes training with supplemental mirrors.
What should Massachusetts road test candidates know about mirrors?
Massachusetts road test candidates should show steady, visible mirror use and head checks throughout the test. The Massachusetts Driver’s Manual tells applicants to look carefully and signal properly before changing lanes, and the examiner watches whether you are aware of your own actions and those of other drivers. Clear, visible mirror checks and head checks help show that awareness.
- Adjust your seat and mirrors before the examiner asks you to start.
- Check mirrors before every stop, turn and lane change.
- Turn your head for blind-spot checks when pulling away from the curb and changing lanes.
- Look back over your shoulder when reversing, not just at a screen.
Learn more in our guides to the Massachusetts RMV road test and how to pass your driver’s test on the first try, or book road test preparation with CMSC.
Why Massachusetts Drivers Choose CMSC
Habits that last. CMSC instructors teach the pre-drive routine, mirror checks and head checks as core driving habits, so they feel automatic by road test day.
Experience you can trust. Central Mass Safety Council was founded in 1987 and has trained more than 100,000 students and adults with more than 75 instructors.
Road test support. CMSC hosts weekend RMV road tests and offers a sponsor and car for road tests, so you can test in a car you already know.
Training for every driver. Teen and adult drivers ed, advanced training and adaptive driving instruction help every driver see more and react sooner.




