Driving School

Already licensed? Click to level up
your career at our CDL School

What to Do If Brakes Fail While Driving: Step by Step

Ishant

Ishant

November 18, 2026 at 9:00 am

You press the brake pedal and it sinks lower than it should, or the car barely slows down. Panic is the natural reaction, and panic is what turns a brake problem into a crash. Total brake failure is rare in modern cars, but when it happens, the drivers who stay calm and follow a plan usually stop safely.

This guide explains what to do if brakes fail while driving, step by step: how to pump the brakes with and without ABS, how to use the parking brake without skidding, how to downshift, where to steer, what never to do, and the warning signs that tell you to get your brakes checked before they fail.

Quick Summary

If your brakes fail while driving, stay calm, take your foot off the gas, turn on your hazard lights and pump the brake pedal quickly to try to rebuild pressure. Shift to a lower gear, slowly apply the parking brake, and steer toward an open, safe place to stop. Never shift into neutral at speed or turn the key to the lock position.

  • Pumping rebuilds pressure: pumping the pedal quickly several times can restore some braking when the pedal goes soft.
  • ABS changes normal hard stops: in a normal emergency stop with working ABS, press and hold firmly instead of pumping.
  • The parking brake is a backup: apply it gradually, never yank it, and release slightly if the car starts to skid.
  • Lower gears slow the car: engine braking helps you shed speed without the brake pedal.
  • The ignition goes to OFF, never LOCK: the lock position can lock your steering wheel.
  • Warning signs come first: a soft pedal, grinding noise or a red brake light are reasons to get the brakes checked right away.
What your brake pedal is telling you, and the first thing to do
Pedal feel What it may mean First action
Soft or spongy Air or a leak in the brake system, low brake fluid Pump the pedal, slow down, get off the road and have it checked
Sinks to the floor Major loss of hydraulic pressure Pump quickly, downshift, apply the parking brake gradually
Hard and barely moves Possible problem with power assist Press much harder with steady force, then stop safely
Pedal blocked Something under the pedal, such as a floor mat Clear it only if you can do so without looking away from the road
Pulses during a hard stop Normal anti-lock brake operation Keep firm, steady pressure and steer around hazards

Want to practice emergency braking and crash avoidance with an instructor? Contact CMSC Driving School about SKIDZ School and advanced training.

What should you do first if your brakes fail while driving?

The first thing to do if your brakes fail while driving is stay calm and keep control of the steering. The car will not stop on its own right away, so your job is to slow it down using every tool you have while keeping it pointed somewhere safe. Work through these steps in order.

  1. Take your foot off the gas and turn off cruise control if it is on.
  2. Turn on your hazard lights to warn drivers around you. Sound the horn if you need to get attention.
  3. Pump the brake pedal quickly several times. This can rebuild hydraulic pressure in the system. If pressure returns, press firmly and hold.
  4. Shift to a lower gear to use engine braking.
  5. Slowly apply the parking brake, increasing the pressure gradually.
  6. Steer toward a safe place to stop, such as an open shoulder, an empty lot or an uphill road.
  7. Once stopped, keep the parking brake on and do not drive the car again until it is repaired.

Quickly check that nothing is jammed under the pedal. A floor mat that slides forward can block the brake pedal, but only clear it if you can do so without taking your eyes off the road.

Should you pump the brakes? ABS vs non-ABS cars explained

When your brakes fail and the pedal goes soft or sinks, pump it quickly several times to try to rebuild pressure, whether or not your car has anti-lock brakes. That is different from a normal emergency stop with working brakes. In a normal hard stop, a car with ABS needs firm, continuous pressure on the pedal, while a car without ABS may need the brakes pumped to avoid locking the wheels.

How to use the brake pedal in a failure vs a normal emergency stop
Situation Car with ABS Car without ABS
Brakes working, sudden hard stop Press firmly and hold, do not pump, steer around hazards Press and release repeatedly to avoid locking the wheels
Pedal soft or sinks to the floor Pump quickly to try to rebuild pressure Pump quickly to try to rebuild pressure
Pressure comes back Press firmly and hold to slow down Brake firmly without locking the wheels
Pressure does not come back Downshift and use the parking brake gradually Downshift and use the parking brake gradually

How do you know if your car has ABS?

Most modern cars have anti-lock brakes. When you start the car, an amber ABS light usually lights up on the dashboard for a moment and then goes out. Your owner’s manual will confirm it. Knowing this before an emergency tells you how your brake pedal should feel in a hard stop.

How do you use the parking brake without skidding?

Use the parking brake to slow down by applying it slowly and gradually, never all at once. The parking brake usually works on the rear wheels, so yanking it hard at speed can lock them and send the car into a skid. If you feel the rear of the car start to slide, ease off the parking brake slightly until the tires grip again.

  • Hand lever: hold the release button in so the lever does not lock, and pull up slowly.
  • Foot pedal: press it down gradually. Some foot parking brakes have a separate release handle.
  • Electronic button or switch: in some cars, holding the switch up applies braking while the car is moving, and braking stops when you let go. Check your owner’s manual now so you know how your car works.

Use the parking brake now and then during normal parking. A brake that is never used can stiffen, and you want it to work when you need it most.

How do you downshift to slow down?

Downshift by moving to a lower gear one step at a time, which uses the engine to slow the car. In an automatic, shift from D to a lower range such as L, 2 or 1, or use the paddle shifters or manual mode if your car has them. In a manual, shift down one gear at a time and let the clutch out smoothly each time.

  • Shift down gradually. Dropping several gears at once at high speed can make the wheels lose grip.
  • Combine downshifting with the parking brake to slow down faster.
  • Keep steering smoothly while you shift.

Drivers learning a manual car can read our guide to half clutch driving for more on clutch control.

How do you stop a car without brakes if nothing else works?

If pumping, downshifting and the parking brake are not stopping the car, steer toward the safest place you can find to lose speed. An open place to steer into or an uphill road will slow the car naturally. A grassy shoulder or a gravel area adds drag and is far better than a crowded intersection.

  • Look for an uphill road or ramp. Gravity slows the car.
  • Use open ground such as an empty parking lot or a wide, clear shoulder.
  • Keep steering inputs small so the car stays under control.
  • As a last resort, turn the ignition to OFF. Never turn it to LOCK, because that can lock your steering wheel. In cars with a push-button start, check your owner’s manual for how to shut the engine off while moving, and remember power steering and power brake assist will be lost.

What should you never do when your brakes fail?

When your brakes fail, never do anything that takes away your control of the car. Some instincts feel helpful but make things worse.

  • Do not shift into neutral at speed. You lose engine braking entirely.
  • Do not turn the key to LOCK. It can lock the steering wheel.
  • Do not yank the parking brake. It can lock the rear wheels and spin the car.
  • Do not jump out of the car. You are far safer staying buckled in and steering.
  • Do not swerve sharply. Sudden steering at speed can roll or spin the car.
  • Do not drive on after the car stops. Have it towed and repaired.

What should you do after the car stops?

After the car stops, secure it and stay safe while you get help. Keep the parking brake on, leave the hazard lights flashing and move everyone away from traffic if it is safe to get out. Call for a tow rather than trying to drive to a repair shop, even if the brakes seem to work again.

  1. Put the car in park with the parking brake set.
  2. Keep hazard lights on. Set out reflective triangles if you have them and it is safe.
  3. Stand well away from traffic, not behind or beside the car.
  4. Call for a tow and have a mechanic inspect the brakes.
  5. Report any crash. In Massachusetts, a crash operator report is due within 5 days if anyone is hurt or damage to any one vehicle or property exceeds $1,000.

What are the warning signs your brakes are going out?

Brakes usually give warning signs before they fail. Catching them early is the best way to make sure you never need the emergency steps above. If you notice any of these, get your brakes inspected soon.

Brake warning signs and how urgently to act on each one
Warning sign What it can point to How urgent
Red brake warning light stays on Parking brake still on, low brake fluid or a brake system fault Stop safely and check right away
Soft, spongy or sinking pedal Air or a leak in the brake lines, low fluid Stop driving and get it checked
Fluid spots near a wheel Brake fluid leak Do not drive until inspected
Grinding or metal-on-metal noise Badly worn brake pads Get it checked as soon as possible
Squealing when braking Brake pads wearing down Schedule an inspection soon
Car pulls to one side when braking Uneven brakes or a sticking part Schedule an inspection soon
Longer stopping distances Worn pads, fluid problems or overheated brakes Get it checked as soon as possible
Burning smell after braking Overheated brakes or a dragging brake Pull over safely and let them cool

Why does your brake pedal feel spongy or sink to the floor?

A spongy brake pedal usually means there is air in the brake lines or the brake fluid is low, often because of a leak. Brakes work by pushing fluid through the lines, and air compresses where fluid does not, so the pedal feels soft. A pedal that sinks to the floor points to a bigger loss of pressure. Both are reasons to stop driving and have the car inspected.

Brakes can also feel weaker after long, steady downhill braking, when they get very hot. On long hills, shift to a lower gear so the engine does part of the work.

What do the red brake light and the ABS light mean?

A red brake warning light usually means the parking brake is still on, the brake fluid may be low or there is a problem in the brake system. First make sure the parking brake is fully released. If the light stays on, car makers advise parking in a safe place and having the brakes checked before driving further.

An amber ABS light points to an issue in the anti-lock brake system. Your regular brakes may still work, but the anti-lock function may not, so drive carefully and have it checked. Your owner’s manual explains exactly what each light means in your car.

Does the Massachusetts inspection check your brakes?

Yes, the Massachusetts annual vehicle inspection includes brake tests. All vehicles registered in Massachusetts must pass a yearly inspection, and the inspection standards reject a vehicle if the parking brake will not hold, if brake pedal height cannot be maintained, or if the brake failure warning light comes on.

Passing inspection does not mean your brakes will stay healthy all year. Pads wear and fluid ages between inspections, so watch for the warning signs above. Before a road test, the car you bring also has to be in safe working order. Our guide to Massachusetts road test vehicle requirements explains what examiners check.

How can new drivers practice for a brake emergency?

New drivers can practice for a brake emergency by learning hard braking, parking brake use and crash avoidance in a controlled setting with an instructor. Practicing the steps once in a safe place makes them much easier to remember under pressure.

  • Find your parking brake and practice applying it gradually while parked, then at walking speed in an empty lot with a supervising driver.
  • Feel your ABS work. A hard stop in an empty lot shows you what pedal pulsing feels like.
  • Train on a closed track. CMSC’s SKIDZ School crash avoidance program is an RMV-certified Driver Skills Development Program with classroom and in-vehicle training on a skid track.
  • Learn to scan ahead. Spotting escape routes early is a core part of a defensive driving course in Massachusetts.

Teens can build these skills in teen drivers ed, adults in adult drivers ed, and businesses can protect employees with fleet driver training. Drivers coming back after time away may also find our guide to returning to driving after years off the road helpful.

Why Massachusetts Drivers Choose CMSC

Emergency skills on a real track. CMSC’s West Boylston headquarters has one of only two skid tracks in Massachusetts, where drivers practice crash avoidance and skid control with a veteran instructor.

An RMV-certified program. SKIDZ School is CMSC’s RMV-certified Driver Skills Development Program, combining classroom instruction with in-vehicle advanced training, and it is part of the training CMSC uses for police, fire and emergency vehicle operators.

Decades of experience. Central Mass Safety Council was founded in 1987 and has trained more than 100,000 students and adults with more than 75 instructors.

Training for every stage. From first lessons to advanced driver training, CMSC helps drivers stay calm and in control when something goes wrong.

Frequently Asked Questions

Related posts